Original implementation only checked whether the user had _selected_ the
clock, not whether it had actually switched to the clock or not. For
almost all cases, this made this function either a no-op, if you _had_
selected the clock, or a blocking loop if you hadn't selected it ahead
of time.
Fixes github issue #687
This reverts commit aa5e108553ace3079c6087dec796b9e58fe45fa4.
This commit was not meant to land yet, it should have gone for review, and
doesn't yet include all the parts it should touch.
replace bulky hardcoded wait for set and wait for clear with a single asynch
routine. Leave the blocking routines in for compatibility at this point.
NOUP: should be added to other rcc.c files too.
L4 and F3 actually have the same bits to write in the same order, but F3 hides
the name of the deep power down bit. Keep the like that for now, but there's a
standard API for enabling and disabling the regulator.
The adc v2 periph has the same register map, but comes in two flavours, one
supporting injected channels, more watchdogs, per channel sampling times and
so on, and one "simple" version.
Pull up the f3 and f0 portions into the appropriate files, after comparing with
L0 and L4 reference manuals, even if those are not fully landed yet.
The f0, f30x and l0 have a very similar "v2" adc peripheral.
Start extracting out some of the common code, and fix the glaring bug in
adc_power_down that was affecting them both.
This is not intended to be a fully comprehensive extraction, just the first
easy steps.
The adc peripheral on F30x is the same as F0, L0 and L4. In the reference
manuals, the following names are used.
F3: CFGR (no CFGR2)
F0 and L0: CFGR1 and CFGR2
L4: CFGR and CFGR2
Moving to a single consistent name, that's more likely to be inline with future
part numbers makes it much easier to extract common driver code for the
peripheral.
While all bit defines are moved to the CFGR1 style, core register definitions:
ADC_CFGR(adc) and ADCx_CFGR are kept to match the original register name in the
reference manual.
Fixes Github issue #548
There are as many SMPRx registers are needed for channels supported, and on all
other families, the field definitions are just ADC_SMPR_SMP_XXX. For
consistency, and to avoid any confusion or duplication, use the same style here
too. Drop silly unused per channel definitions that have no purpose.
At least temp sensor, vrefint and vbat/vlcd should have consistent names and
consistent doxygen.
Dropped channel definitions that are the same as the raw number.
Original commits, while appearing clean and tidy, hadn't even been
compile tested. Trust no-one. Not even Scully.
Fixes: 770878e7b4ac12513e121e087261ca0972ba04e6
Fixes: 86d20ef00c00a14d7a4f0b834b9b608b2dd3638a
Fixes: 05ff0df32226dc28e22b98afde07bb886af9ddc9
As done by esden for the F4, remove typedefs and add prefixes to clock enums
This extends this to all stm32 families.
Let's not hide the fact that these variables are structs/enums.
We are filling up the namespace badly enough, we should be prefixing as
much as we can with the module names at least. As users we already run
often enough in namespace colisions we don't have to make it worse.
* CLOCK_3V3_xxx enums renamed to RCC_CLOCK_3V3_xxx
* clock enums (PLL, HSI, HSE ...) prefixed with RCC_
* scale enum of pwr module prefixed with PWR_
Based on the f0 support, which has identical functionality, but with doxygen
added. Bits renamed as they are only HSE prediv on some targets, and makes
things more consistent with the f0.
Fixes part of github issue #560
This function was badly copied and pasted from the f4 library, where there are
two functions, rcc_set_main_pll_hsi and rcc_set_main_pll_hse which combine
source, multipliers, dividers and other pll factors.
On F3, (not all of them, but the ones we support now), the function as
implemented has nothing to do with hsi / hse, and instead is simply selecting
the PLL multiplier.
Copypasta from f4 rcc code was only modified to shift the result, but not clear
the existing settings properly. Add mask/shift definitions and use them
properly.
All the macro arguments that are user supplied, or potentially, wrap properly
in () as good practice.
Probably missed one or two, and a lot of them are possibly unnecessary, but
it's straightforward to just do it always.
Fixes github issue #321
The breaking changes here changes in header location, and changes in driver
name passed down to the usb stack.
Changes affect: stm32f102/f103, stm32l1, and some f3 parts
* instead of the confusingly generic "usb" use the name "st_usbfs" for the USB
Full speed peripheral ST provides in a variety of their stm32 products.
Include directives should change as:
#include <libopencm3/stm32/usb.h> => <libopencm3/stm32/st_usbfs.h>
* instead of the confusingly specific "f103" name for the driver, use
"st_usbfs_v1" [BREAKING_CHANGE]
Instead of:
usbd_init(&stm32f103_usb_driver, .....) ==>
usbd_init(&st_usbfs_v1_usb_driver, .....) ==>
The purpose of these changes is to reduce some confusion around naming, but
primarily to prepare for the "v2" peripheral available on stm32f0/l0 and some
f3 devices.
Work by Frantisek Burian, Kuldeep Singh Dhaka, Robin Kreis, fenugrec and zyp
on irc, and all those forgotten.
All STM32 family pwr.h must use LIBOPENCM3_PWR_H as include guard so that
pwr_common.h can detect that it has been referenced by pwr.h for
each family. F2 and F3 had the wrong include guard.
Fixes Github issue #513
The f3 adc has separate bits for end of conversion and end of sequence.
Support those fully, with the regular enable/disable irq methods, and
the flag checking methods.
Discovered in github bug: #493
This code was copied from the f4, and blindly modified to make it seem
to work. The f3 has separate flags for EOC and EOS, it doesn't use a
second bit to configure what the EOC bit does.
Consequently, update the documentation to correctly indicate that the
EOC bits are only set per conversion.
Discovered in github bug: #493
This adds MCO source selection to some targets, and removes and standardizes
the mask/shift usage for all targets. For devices that support MCO2, this
supports only MCO1. No attempt has been made to extract MCO prescaler, which
is not available on all F1 and F3.
Rename rcc_ppre1_frequency and rcc_ppre2_frequency to rcc_apb1_frequency and rcc_apb2_frequency
Also add rcc_ahb_frequency (although it is not set correctly in all cases) which will be fixed by
the rcc commits later. Also fixup the only use in the library of these variables, the USART code.
And fix the typos that resulted
Make l1 generic too
Latest versions of all reference manuals refer to the address as SPIx_BASE, and
simply name some of the individual registers as SPI_I2SXXXX. Likewise, the
interrupts are simply SPIx, not SPIx/I2Sx. Rather than hacking more duplicates
into the F0 and L0 parts where this was turning up, remove the pointless _I2S_
from SPI2/SPI3 and make it all consistent
Compile tested only, with the examples collection.
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Fixes#331Fixes#347
to remove variations, redundancies, add missing, fix errors. All c files
refer only to the dispatch style headers in /include/stm32. Those headers
#include memorymap.h and cm3/common.h. All references to
these are removed from the family specific headers. Ethernet untouched as
it appears incomplete.
Added dummy spi.c for F0/F3. Fix some doxygen anomalies.
When compiling with all warnings enabled, some defines can lead to
warning due to missing unsigned type suffix:
warning: integer overflow in expression [-Woverflow]
This fix should not affected behavior at all, since calculation with
such overflows lead to the same actual address when writing to that
location. However, it makes the warning disappear and also defines
the right data type for a memory location.
This pulls out all the common header definitions for the F1, L1, F4 and F37x
parts. It's verified against the datasheet for F2 as well, but we don't have
any good F2 test boards or any support for that yet. (The F2 header would be
_exactly_ the same as the F4 header, so it's a target for a future round of
unification, not this one)
Tested with f1, f4 and l1 examples from the examples repository.
