Instead of every "simple" target having their own duplicate file with
all the section mappings, just provide a single, simple,
"cortex-m-generic.ld" that works with our startup code and any simple
rom/ram system. This also drops the pointless copying of files all over
the place. Using -L flags properly is sufficient, and the standard file
is now in the root of the library already.
Somewhat replaces some earlier work done by hg/lg, but much more
complete, so we kept it as is, because it's bringing in even more parts
after this.
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
The original submitter of this squished everything into one series, and
has not returned. The code mostly appears good, and review comments were
followed for the most part. The project doesn't really maintain any
testing or board farm for sam3/sam4 parts, so we're going to just trust
our users.
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
sam/4l: IRQ Configuration file (irq.json)
sam/4l: Basic Memory Map.
sam/4l: GPIO Defines.
sam/4l: GPIO Functions
Added everything that needed to compile the library: Makefile, Linker
Script and common includes.
sam/4l: SCIF function to start OSC.
sam/4l: GPIO Enable/Disable and Multiplexing configuration functions.
sam/4l: PLL Clock configuration.
sam/4l: Peripheral clock configuration and basic USART support.
sam: USART Character length configuration.
sam/4l: Generic Clock configuration functions.
sam/4l: Analog to Digital Converter Interface (ADCIFE) basic support.
Originally sourced from: https://github.com/libopencm3/libopencm3/pull/382
fixed some typos from the manual and poor merging/rebaseing,
and one judgment call on using a specific name for a conflicting
bit definition.
The stm32fx07 is common DesignWare IP, used in both STM32 and EFM32 chips.
Rename the files to make this more clear, and easier to use in other
targets.
Makefile doesn't even refer to it, and it's empty anyway. Not required
for doxygen purposes, (anymore?) so just drop it. File had _never_ been
included in the f3 makefile.
The ADC v2 peripheral doesn't have the same behaviour of starting, where
the hardware clears the bit immediately, on v2, it is not cleared until
the ADC is stopped, or the end of sequence flag is set.
Fixes https://github.com/libopencm3/libopencm3/issues/557
The SPI br parameter has always been the 3 bit fpclk divider field, and
was never a target or explicit bit rate. Correct the comments, and drop
the duplicate commentary that wasn't included in the doxygen output
anyway.
Fixes: a7a3770d Add initial SPI code
Use the usart-common base plus the usart-v2 code, instead of private
implementations. Less code, more common apis across targets.
Of note is the trick to make F0 look like it has an APB2 bus. It's the
only stm32 that doesn't have a documented APB2 bus, but still has
peripherals enabled via an "APB2" register, and they match how other
targets have an APB2. Simply make APB2 an alias of APB1, as it's only
used for clock speed detection.
This function was using apb1 for quite a few families instead of apb2.
This only mattered for L1 and F3, and for USART1/USART6, and only if
apb1 speed != apb2 speed.
Instead of using families explicitly, just check for the peripherals
themselves. On F0,F1,F2,F3,F4,F7,H7,L0,L1,L4, usart1/6 are _always_ in
the rcc_apb2 register and the other uarts are all on apb1.
(F0 doesn't actually _have_ apb2, but it's still called the apb2
register)
