Complements #204.
STLinkV2-1 has F103CB on board! F103C8 on older Stlinks can use upper flash
with hopefully acceptable error rate.
For F103C8 devices, user has to give the force option to dfu-utils.
1) This version uses a direction control level shifters. We need to control
the direction of the TMS/SWDIO pin.
2.1) Because we want to support a large voltage range for SRST we use an
external dual MOSFET for asserting and sensing the SRST line. We have
added the hardware version 3 to be handled the same way as version 0.
Meaning using separate pins for assertion and sensing of the SRST line.
2.2) The new SRST sense circuit is inverting, thus we have dedicated
code for hardware version 3 that inverts the SRST status pin on read.
- Remove connect_assert_srst global.
- Attach functions always release reset.
- Platforms provide a method to poll the reset pin.
- Reset on scan is all internal to command.c
- Reset is released on a failed scan. Fixes#111
All BMPM2 prototypes after revision a have their LED0 and LED2 inverted.
Because of that we have bumped the hardware revision to swap the LEDs in
software. This is easier than messing up the routing of the LEDs.
This change has also a practical reason. When flashing and testing the
hardware this change makes it easier to make sure all the LEDs work. Now
when the DFU bootloader is idle it is scanning the LEDs making it easy
to see if one of them has an issue.
In addition to that, the bootloader now indicates when there is data
being flashed using the DFU interface. In cases when one has more than
one device connected and accidently starts flashing a wrong device this
is very useful feature to have.
All source files include general.h first and before anything else.
This inlcludes platform.h and platform_support.h
No header file needs to include to include any of these, but should include
any others needed for it's own declarations.
Hello,
appended 3 patches
- adds a dfu-bootloader appliaction
- uses absolute delays when waiting for pull-up delays on the STLINK
(hopefully fixes issue #30)
Updating the dfu-bootloader by additional application is helpfull for the
STLINK, as for flashing the bootloader by SWDb otherwise jumpers need to be
soldered or external SWD is not possible.
Use like:
- dfu-util -s 0x08002000:leave -D dfu_upgrade.bin
- dfu-util -s 0x08000000:leave -D blackmagic_dfu.bin
- Push reset buttom and reconnect to enter new dfu bootloader
- dfu-util -s 0x08002000:leave -D blackmagic.bin
--
Uwe Bonnes bon@elektron.ikp.physik.tu-darmstadt.de
Institut fuer Kernphysik Schlossgartenstrasse 9 64289 Darmstadt
--------- Tel. 06151 162516 -------- Fax. 06151 164321 ----------
>From fae5022c304a8866f056ea66660ac7ce3809dcf8 Mon Sep 17 00:00:00 2001
From: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Date: Sun, 20 Oct 2013 15:00:36 +0200
Subject: F1: Prepare to update dfu bootloader via DFU with additional
application.
o Prevent probe from inadvertently powering target. If PWR_BR is
allowed to float, the gate on Q1 (blackmagic_mini) will tend to be
close enough to zero to turn the transistor on. We activate the
internal pull-up on this IO pin to force the transistor off.
USB UART seems to work fine at 115.2Kbps or 230.4Kbps, but starts to drop characters
as the data rate goes higher. This commit changes the usbuart ISR to fill a software
FIFO, and adds a low priority timer interrupt to run deferred processing to drain a
FIFO and send USB CDCACM packets, rather than calling the usb send within the UART
ISR.
Tested on native platform, up to 1.5MBps.
