This adds MCO source selection to some targets, and removes and standardizes
the mask/shift usage for all targets. For devices that support MCO2, this
supports only MCO1. No attempt has been made to extract MCO prescaler, which
is not available on all F1 and F3.
Rename rcc_ppre1_frequency and rcc_ppre2_frequency to rcc_apb1_frequency and rcc_apb2_frequency
Also add rcc_ahb_frequency (although it is not set correctly in all cases) which will be fixed by
the rcc commits later. Also fixup the only use in the library of these variables, the USART code.
And fix the typos that resulted
Make l1 generic too
Pulls out duplicate calls from f0/rcc.c and uses the common version which
also means that f0 can use rcc_peripheral_enable() now which is in common
but not the old rcc versions.
Latest versions of all reference manuals refer to the address as SPIx_BASE, and
simply name some of the individual registers as SPI_I2SXXXX. Likewise, the
interrupts are simply SPIx, not SPIx/I2Sx. Rather than hacking more duplicates
into the F0 and L0 parts where this was turning up, remove the pointless _I2S_
from SPI2/SPI3 and make it all consistent
Compile tested only, with the examples collection.
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Fixes#331Fixes#347
This commit has been based on kuldeepdhaka's pioneer work, but it was reformatted to apply libopencm3 inclusion tree correctly.
timer_common_all.c now supports new rcc_periph_reset_pulse function for all families.
to remove variations, redundancies, add missing, fix errors. All c files
refer only to the dispatch style headers in /include/stm32. Those headers
#include memorymap.h and cm3/common.h. All references to
these are removed from the family specific headers. Ethernet untouched as
it appears incomplete.
Added dummy spi.c for F0/F3. Fix some doxygen anomalies.
When compiling with all warnings enabled, some defines can lead to
warning due to missing unsigned type suffix:
warning: integer overflow in expression [-Woverflow]
This fix should not affected behavior at all, since calculation with
such overflows lead to the same actual address when writing to that
location. However, it makes the warning disappear and also defines
the right data type for a memory location.
Extension of code for STM32F1 to allow for dual bank series XL.
Small changes to documentation for F2, F4 and L1 to add a parameter reference.
Tested with STM32F103RBT6
(note: tests show that the PG bit must be cleared after programming, otherwise
a subsequent erase attempt fails. This has been added to flash_program_half_word
for F0 and F1 only. A fix for the other families is not included in this PR.)
So that the navigation pane works correctly in browsers.
Some additional doc fixes put in where found (but many more still to go).
Added some dummy .c and .h files to bring the associated docs into line.
makefile changed to allow 'make html' as well as 'make doc' (the latter only does html anyway).
This converts all the YAML files to JSON files, as json parsing is built
into python instead of being a separate library requiring installation.
YAML is a superset of JSON, but putting comments in is not quite as obvious
as it is in yaml.
The following glue was used to convert yaml to json:
python -c 'import sys, yaml, json; json.dump(yaml.load(sys.stdin), sys.stdout, indent=4)' < $1 > $2
Clearly I haven't tested this on every single platform, and this
doesn't address the large blobs of yaml in the lpc4300 scripts directory,
only the cortex NVIC generation process.
I've tested a few IRQ driven example apps, and I've checked the generated
output of some known cases like the LM3s that has explicit gaps, and they are
all generated correctly.
The value '6' was twice in the table and all higher frequencies are
shifted. The values are now fitting the table in 'STM32F05xxx/06xxx advanced
ARM-based 32-bit MCUs', page 101.
PLL frequencies have been measured by selecting
rcc_set_mco(RCC_CFGR_MCO_SYSCLK);
and measuring the output with an oscilloscope. 8, 16, 24, 32, 40 and 48 MHz
work fine from the HSI base.
Add memorymap entries for ST calibration data, the vref internal, and the temp
sensor at 30C and 110C for the parts that provide this data.
F1 and F2 do not appear to have this anywhere.
The common code wasn't being included in L1 builds, even though the headers now
included the correct definitions.
This combines the two f0 and f3 spi files, which previously differed only in
the number of spi peripherals defined.
Files were renamed to the full "l1f124" style, not because I like it, but
because it's the convention we have, so it's best to apply it rigourously.
Tested on L1 and F100 boards, compile tested only for others, but the examples
repository all compiles too. (Though the lack of SPI examples for all
platforms was how this broke in the first place)
STM32L1 has a different set of offsets, not just a different base
address, so we can't have common registers definitions. Also, out of
F0,F1,F2,F3,F4,L1, only the F1 has the odd note about 2x16bit registers
and 2x32bit registers with one 16bit register marked as "This field
value is also reserved for a future feature." Therefore, replace the
awkward reading out as multiple words and just copy them in.
F0,F2,F3,F4 were missing definitions altogether.
This does _not_ attempt to address the problem of the mismatched base
addresses for Medium+ and High Density L1 parts.
