This commit has been based on kuldeepdhaka's pioneer work, but it was reformatted to apply libopencm3 inclusion tree correctly.
timer_common_all.c now supports new rcc_periph_reset_pulse function for all families.
to remove variations, redundancies, add missing, fix errors. All c files
refer only to the dispatch style headers in /include/stm32. Those headers
#include memorymap.h and cm3/common.h. All references to
these are removed from the family specific headers. Ethernet untouched as
it appears incomplete.
Added dummy spi.c for F0/F3. Fix some doxygen anomalies.
When compiling with all warnings enabled, some defines can lead to
warning due to missing unsigned type suffix:
warning: integer overflow in expression [-Woverflow]
This fix should not affected behavior at all, since calculation with
such overflows lead to the same actual address when writing to that
location. However, it makes the warning disappear and also defines
the right data type for a memory location.
Extension of code for STM32F1 to allow for dual bank series XL.
Small changes to documentation for F2, F4 and L1 to add a parameter reference.
Tested with STM32F103RBT6
(note: tests show that the PG bit must be cleared after programming, otherwise
a subsequent erase attempt fails. This has been added to flash_program_half_word
for F0 and F1 only. A fix for the other families is not included in this PR.)
This unifies stm32f1, l1, and f4 convenience functions for adc. The code
should be useable for f2 and f37x as well, but that needs hardware for testing,
and there was no existing implementation. This is the reason for the
"adc_common_v1.c" name, as trying to put all the different families into the
common file name has become too cumbersome.
All of the deprecated routines have been dropped, they've been marked
deprecated for a very long time now, and porting them seemed unnecessary.
This has been tested on f1, l1 and f4 discovery boards, and is based on some
existing l1/f1 unification code from
https://github.com/karlp/libopencm3/tree/rme_l1_master
This pulls out all the common header definitions for the F1, L1, F4 and F37x
parts. It's verified against the datasheet for F2 as well, but we don't have
any good F2 test boards or any support for that yet. (The F2 header would be
_exactly_ the same as the F4 header, so it's a target for a future round of
unification, not this one)
Tested with f1, f4 and l1 examples from the examples repository.
So that the navigation pane works correctly in browsers.
Some additional doc fixes put in where found (but many more still to go).
Added some dummy .c and .h files to bring the associated docs into line.
makefile changed to allow 'make html' as well as 'make doc' (the latter only does html anyway).
This converts all the YAML files to JSON files, as json parsing is built
into python instead of being a separate library requiring installation.
YAML is a superset of JSON, but putting comments in is not quite as obvious
as it is in yaml.
The following glue was used to convert yaml to json:
python -c 'import sys, yaml, json; json.dump(yaml.load(sys.stdin), sys.stdout, indent=4)' < $1 > $2
Clearly I haven't tested this on every single platform, and this
doesn't address the large blobs of yaml in the lpc4300 scripts directory,
only the cortex NVIC generation process.
I've tested a few IRQ driven example apps, and I've checked the generated
output of some known cases like the LM3s that has explicit gaps, and they are
all generated correctly.
The value '6' was twice in the table and all higher frequencies are
shifted. The values are now fitting the table in 'STM32F05xxx/06xxx advanced
ARM-based 32-bit MCUs', page 101.
PLL frequencies have been measured by selecting
rcc_set_mco(RCC_CFGR_MCO_SYSCLK);
and measuring the output with an oscilloscope. 8, 16, 24, 32, 40 and 48 MHz
work fine from the HSI base.
Add memorymap entries for ST calibration data, the vref internal, and the temp
sensor at 30C and 110C for the parts that provide this data.
F1 and F2 do not appear to have this anywhere.
According to RM0090, page 301, paragraph 11.13.12 Note. (For F4, for F1 and F3 is it in the corresponding manuals)
The JSQR are filled always ending at SQR4 ie for those lists we must set this list:
(A) -> JSQ4 = A,
(A,B) -> JSQ3 = A, JSQ4 = B,
(A,B,C) -> JSQ2 = A, JSQ3 = B, JSQ4 = C,
(A,B,C,D) -> JSQ1 = A, JSQ2 = B, JSQ3 = C, JSQ4 = D,
The readed values are in correct order, starting from JDR1:
(A) -> JDR1 = A,
(A,B) -> JDR1 = A, JDR2 = B,
(A,B,C) -> JDR1 = A, JDR2 = B, JDR3 = C,
(A,B,C,D) -> JDR1 = A, JDR2 = B, JDR3 = C, JDR4 = D,
