The value '6' was twice in the table and all higher frequencies are
shifted. The values are now fitting the table in 'STM32F05xxx/06xxx advanced
ARM-based 32-bit MCUs', page 101.
PLL frequencies have been measured by selecting
rcc_set_mco(RCC_CFGR_MCO_SYSCLK);
and measuring the output with an oscilloscope. 8, 16, 24, 32, 40 and 48 MHz
work fine from the HSI base.
The STM32F05xxx/06xxx manual describes on p.98 (Sec 7.4.1) the RCC_CR
register, on which it says that bit 24 is the PLLON bit which has to be
enabled before using the PLL. This causes the PLL to be enabled with
rcc_osc_on(PLL).
Add memorymap entries for ST calibration data, the vref internal, and the temp
sensor at 30C and 110C for the parts that provide this data.
F1 and F2 do not appear to have this anywhere.
According to RM0090, page 301, paragraph 11.13.12 Note. (For F4, for F1 and F3 is it in the corresponding manuals)
The JSQR are filled always ending at SQR4 ie for those lists we must set this list:
(A) -> JSQ4 = A,
(A,B) -> JSQ3 = A, JSQ4 = B,
(A,B,C) -> JSQ2 = A, JSQ3 = B, JSQ4 = C,
(A,B,C,D) -> JSQ1 = A, JSQ2 = B, JSQ3 = C, JSQ4 = D,
The readed values are in correct order, starting from JDR1:
(A) -> JDR1 = A,
(A,B) -> JDR1 = A, JDR2 = B,
(A,B,C) -> JDR1 = A, JDR2 = B, JDR3 = C,
(A,B,C,D) -> JDR1 = A, JDR2 = B, JDR3 = C, JDR4 = D,
ITM Stimulus ports need to be accessible with different sizes
The amount of data written out is determined by the size of the write.
Writing a full 32 bit value when you only need 8 for printf() style
substantially reduces the available bandwidth of the SWO
Note: this is an API change for doing 32bit writes.
Old:
ITM_STIM[stimulus_port] = value
New:
ITM_STIM32(stimulus_port) = value
This api is much more in common with some of the other registers that
behave this way. As there's very little (if any) code already using
this API, it's a good time to fix it permanently.
Remove misleading ITM register definitions
ITM_SSPSR is the supported parallel trace size, in _bits_
ITM_CSPSR is in _bits_ as well. There's really no advantage in even
having these sorts of definitions in libopencm3, as these settings are
normally controlled from the debugger side, not the target itself.
Lock and lock status register definitions were added, as per ARM:
"For ARMv7-M, the component ID registers are required for the ROM table,
and the CoreSight management lock access mechanism is defined for the
DWT, ITM, FPB and TPIU blocks."
The common code wasn't being included in L1 builds, even though the headers now
included the correct definitions.
This combines the two f0 and f3 spi files, which previously differed only in
the number of spi peripherals defined.
Files were renamed to the full "l1f124" style, not because I like it, but
because it's the convention we have, so it's best to apply it rigourously.
Tested on L1 and F100 boards, compile tested only for others, but the examples
repository all compiles too. (Though the lack of SPI examples for all
platforms was how this broke in the first place)
DFF exists at bit 11 for f1, f2, f4 and l1, but the f0 and f3 have that bit as
CRC len and use CR2 for data size bits instead. The merging of the F3 and F0
and attempts to put common data in common places broke the l1 code.
F3 and F0 SPI headers are still almost completely identical.
use stdint-types, not short types
remove info on file stucture of examples, this was removed some time ago,
add reference to libopencm3-examples instead.
STM32L1 has a different set of offsets, not just a different base
address, so we can't have common registers definitions. Also, out of
F0,F1,F2,F3,F4,L1, only the F1 has the odd note about 2x16bit registers
and 2x32bit registers with one 16bit register marked as "This field
value is also reserved for a future feature." Therefore, replace the
awkward reading out as multiple words and just copy them in.
F0,F2,F3,F4 were missing definitions altogether.
This does _not_ attempt to address the problem of the mismatched base
addresses for Medium+ and High Density L1 parts.
The f103 usb core should be usable on the l1 as well, and the /f1/rcc
isn't explicitly required anymore. This is an important change to be
able to share the driver.
The direct access definitions to the SHPR1 SHPR2 and SHPR3 were simply
wrong, and though a handy macro for directly reaching any priority field
was provided, the definitions of the fields assumed direct access to the
registers.
Provide field definitions that match the handy macro, and correct the
direct access definitions for people wishing to use them.
